Contact Us
TEL: +86-511-85722368
Mob: +86-15805290338
E-mail: tyb@cn-meihua.com
Address: Pan Zonglu, Ding MAO Development Zone, Zhenjiang City, Jiangsu Province

Pneumatic Energy-storing Spot Welding Machine

PM1060Q / PM1080Q/ P1108Q PM1060Q/ P1108Q type energy storage spot welders are a new type of welding equipment which adopts MPU control, silicon controlled discharge and pneumatic compression. PM1080Q type energy storage spot welding machine is a new type of welding equipment adopts MPU control,...

PM1060Q / PM1080Q/ P1108Q

PM1060Q/ P1108Q type energy storage spot welders are a new type of welding equipment which adopts MPU control, silicon controlled discharge and pneumatic compression. PM1080Q type energy storage spot welding machine is a new type of welding equipment adopts MPU control, SCR discharge, pneumatic pressure.  The devices adopt the capacitive energy storage and the principle of releasing large current in a moment to weld the workpiece. The equipments have short welding time and concentrated energy. They can weld non-ferrous metal and black metal well, and the workpiece is not easy to oxidize. Through the change of the electrode, a variety of small sealing cap welding can be carried out.


The PM1080Q type energy storage spot welder is a special welding machine specially designed for the welding steamer. It is composed of the upper welding cylinder and the lower upper top cylinder. In the manual state, the cylinder I on the controller panel controls the upper welding cylinder, and the cylinder II controls the upper top cylinder. Under the working condition, the foot switch is started, the upper cylinder and the welded cylinder move together, and the upper cylinder is shorter than the welded cylinder, so the position is first, then the cylinder is pressed down, welded and pressed for two times.


The three types energy storage spot welding machine to change the traditional AC contactor discharge mode, thyristor controlled discharge, reduce noise, prolong life, safe and reliable. The whole welding procedure is controlled by computer chip, and the control is accurate and reliable.

The two types energy storage spot welding machine can be widely used in electronics, electric vacuum, electrical, hardware, semiconductor, battery etc.. It can be used not only for spot welding, but also for replacement of electrodes and moulds and for various packaging and welding.


1.jpg


PM1060Q

Technical parameters:

1. the maximum storage capacity: 6000J

2. storage: the highest voltage 380V

3. the output voltage of the transformer = 6.0V

4. welding ability brass stainless steel: 2.5+2.5mm  brass: 2.0mm+2.0mm hard aluminum : 1.8mm+1.8 mm

5. power supply: 380V 50HZ 2 phase + zero line

6. gas supply: = 0.5MPa

7. program control: MPU chip control

8. weight: about 800Kg

9. dimensions: L * B * H 1640 x 820 x 1960 (mm)


PM1080Q

Technical parameters:

1. the maximum storage capacity: 8000J

2. storage: the highest voltage 380V

3. the output voltage of the transformer = 6.0V

4. welding ability stainless steel: 3.0mm+3.0mm brass: 2.5mm+2.5mm hard aluminum: 2.0mm+2.0 mm     

5. power supply: 380V 50HZ 2 phase + zero line

6. gas supply: = 0.5MPa

7. program control: MPU chip control

8. weight: about 1000Kg

9. dimensions: L * B * H 1720 x 815 x 1960 (mm)


1.jpg


P1108Q

Technical parameters:

1, maximum storage capacity: 800J

2, storage 380V: maximum voltage

3, transformer output voltage: = 5.5V

4, welding stainless steel: 1.2+1.2mm, brass 0.8+0.8mm

5, power supply: 2 phase, 50HZ, 380V

6, gas supply: = 0.5MPa

7, program control mode: MPU chip control

8, weight: about 140KG

9, dimensions: L * B * H 900 x 650 x 1300 (mm)


Hot Tags: pneumatic energy-storing spot welding machine, China, manufacturers, suppliers, factory, buy, made in China
Inquiry